There is nothing electric about the radiator body, so just like a central heating radiator it can be safely installed anywhere in the bathroom.
Can you have an electric towel rail in a bathroom?
Today’s modern heated towel rails are designed to keep both you and your bathroom feeling wonderfully warm, especially during the cold winter months. Electric towel rails are a safe, efficient, and cost-effective heat source designed especially for bathrooms.
Can you fit an electric towel rail yourself?
They come in a variety of designs and styles to suit your existing decor and personal preference, plus you can even fit them yourself if you have decent electrical wiring and plumbing skills (though you will need to adhere to the Electrical Wiring Regulations for special installations in bathrooms and other “wet” areas …
Can you put a heated towel rail in a shower?
DO NOT try and install an electric radiator, towel rail or heater in your bathroom unless you are a qualified electrician. You should never use plug-in radiators or heaters in your bathroom – whether they are plugged into sockets inside or outside the room.
Are electric towel rails expensive to run?
Electric Towel Rails
These rails avoid the issue of having to switch on the rest of your central heating, however they can be expensive to run due to the power requirements of the heated element within. Essentially, they function similarly to a kettle, though without quite so much short term power usage.
Are electric towel rails any good?
The good news is that an electric towel rail is highly affordable. It can be turned on and off instantly to provide localised heat and will not make any noticeable extra dent in those pesky bills. … Remember, you can dry clothes on these nifty towel rails too!
Do you need an electrician to install a heated towel rail?
Once you have installed a heated towel rail timer you can set it to run for a period of time such as eight hours before your regular shower time. … A heated towel rail time will cost you as little at $40 plus the cost of installation by an electrician which is a quick and simple installation.
Who can fit an electric towel rail?
If you’re having a dual fuel heated towel rail fitted, then this needs to be connected to the hot water central heating system AND to the electrical mains supply, so you’ll either need to find a professional who can legally do both, or get a plumber and an electrician to install it safely and correctly.
How close can an electric towel rail be to a shower?
Zone 1 is the zone above your bath or shower to a height of 2.25m. If you were to install a heated towel rail in this zone, it would need a rating no lower than IPX4. Zone 2 stretches to a 0.6m outside your bath or shower and above your bath or shower if over 2.25m.
Can I put an electric heater in the bathroom?
DO NOT try and install an electric radiator, towel rail or heater in your bathroom unless you are a qualified electrician. … You should never use plug-in radiators or heaters in your bathroom – whether they are plugged into sockets inside or outside the room.
Can you put an electric towel rail upside down?
Turn the towel radiator upside down and screw the electric element into the either side of the towel radiator. Use PTFE tape wrapped clockwise around all male threads to assist in making watertight and complete sealed joints.
Are heated towel rails as good as radiators?
Not only are towel rails a more practical solution than standard radiators, as they’ll keep your towels warm fluffy and dry, but they also make a stylish addition to any bathroom. … A larger bathroom, however, may require another source of heating to sufficiently warm the room.
What liquid do you put in an electric towel rail?
If you want to fill a radiator for electric use, you need a special solution of 90% deionized water and 10% Ethylene Glycol (car anti-freeze). This solution needs to be poured into your electric towel rail before you switch it on, as it is this solution that gets hot and causes your rail to give off heat.
How much water do you put in an electric towel rail?
The entire towel rail does not get hot
Top-up the towel rail by removing one of the top plugs and fill it with water only allowing around 10% of the height for expansion when the water gets hot. If you are refilling a towel warmer from empty then a combination of 85% water and 15% corrosion inhibitor is recommended.